Calculating Metal Weight by Hand: Formulas and Density
By Hamza Bin Maqsood · · 4 min read
The volume × density method for plate, bar and pipe, worked examples, and why tools differ between 7,850 and 7,870 kg/m³.
The one formula
Every metal weight is volume multiplied by density. Keep the units consistent and the arithmetic is short: weight (lb) = volume (in³) × density (lb/in³), or weight (kg) = volume (m³) × density (kg/m³). For a flat piece, volume is length × width × thickness. For a bar or pipe, volume is cross-section area × length.
Densities to use
| Metal | kg/m³ | lb/in³ | lb/ft² per inch |
|---|---|---|---|
| Carbon Steel | 7,850 | 0.2836 | 40.84 |
| Stainless Steel 304 / 316 | 8,000 | 0.2890 | 41.62 |
| Aluminum 6061 / 5052 | 2,700 | 0.0975 | 14.05 |
| Brass C360 (free-cutting) | 8,500 | 0.3071 | 44.22 |
| Copper C110 | 8,940 | 0.3230 | 46.51 |
To convert, 1 lb/in³ = 27,679.9 kg/m³, so 7,850 kg/m³ = 0.2836 lb/in³ = 490.1 lb/ft³ = 40.84 lb/ft² per inch of thickness. For steel, the last figure is the one worth memorising.
Exact conversions
- 1 in = 25.4 mm and 1 ft = 304.8 mm, both exact.
- 1 lb = 0.45359237 kg, exact.
- 1 ft² = 144 in² = 0.09290304 m².
- A 4×8 ft sheet is 32 ft², or 2.973 m². A 1250 × 2500 mm sheet is 3.125 m².
Comparing metals at a glance
For the same volume, aluminum weighs 34% as much as carbon steel, stainless steel is 1.9% heavier, brass 8.3% heavier and copper 13.9% heavier. Those ratios, from 2,700, 8,000, 8,500 and 8,940 kg/m³ against 7,850, make a quick check on any quote: a 4×8 aluminum sheet of the same thickness should weigh a little over a third of the steel one.
Worked example: a plate
A carbon steel plate 48 × 96 in and 1/4 in thick has a volume of 48 × 96 × 0.25 = 1,152 in³. Multiply by 0.2836 lb/in³ and the plate weighs 326.7 lb. In metric, weight (kg) = length (m) × width (m) × thickness (mm) × 7.85, so 1.2192 × 2.4384 × 6.35 × 7.85 = 148.2 kg. Both answers describe the same plate.
Bar and pipe
Bar cross-section area is π/4 × d² for round, s² for square, t × w for flat and (√3/2) × AF² for hex, where AF is the distance across flats. For 1 in round steel bar the area is 0.7854 in², so one foot weighs 0.7854 × 12 × 0.2836 = 2.673 lb. Pipe is hollow, so its area is π × (OD − wall) × wall, which gives 10.69 × (OD − wall) × wall lb/ft for carbon steel in inches. For NPS 2 Schedule 40, 10.69 × (2.375 − 0.154) × 0.154 = 3.66 lb/ft.
More worked examples
Stainless sheet. 14 gauge stainless is 0.0781 in thick, so one square foot weighs 0.0781 × 144 × 0.289 = 3.25 lb, and a 4×8 sheet weighs 104 lb.
Aluminum sheet. 12 gauge aluminum is 0.0808 in: 0.0808 × 144 × 0.0975 = 1.13 lb/ft², or 36.3 lb per 4×8 sheet.
Hex bar. 3/4 in across flats has an area of 0.866 × 0.75² = 0.4871 in², so one foot of carbon steel weighs 0.4871 × 12 × 0.2836 = 1.658 lb.
Metric shortcut. Round steel bar weighs d² × 0.00617 kg/m with d in millimetres, because π/4 × 7,850 ÷ 1,000,000 = 0.00617. A 25 mm bar is 25² × 0.00617 = 3.85 kg/m. Square bar is s² × 0.00785 and flat bar is t × w × 0.00785 kg/m. Pipe in millimetres is 0.02466 × (OD − wall) × wall kg/m.
Order total. Ten 10 ft lengths of 1 in round steel bar are 100 ft, so the order weighs 100 × 2.673 = 267 lb, or 121.2 kg.
Why tools disagree
Four differences explain most mismatches between calculators.
- Density constant. Most references use 7,850 kg/m³ for carbon steel. Some tools use 7,870 or 7,874, the density of pure iron, which is probably the origin of the 7,870 figure. The gap is 0.25%, about 25 kg on 10 tonnes.
- Rounding. 0.2836 against 0.284 lb/in³ is a 0.14% difference, and many printed tables round again at the end.
- Chart conventions. Manufacturers' Standard Gauge weights use 41.82 lb/ft² per inch, 2.4% above the density-based 40.84, so a published 16 gauge weight of 2.500 lb/ft² will not match 2.442.
- Alloy values. Sources list 5052 aluminum at about 2,680 kg/m³ against 2,700 for 6061, a 0.7% gap, and published 304 stainless values cluster around 8,000 kg/m³ without agreeing exactly.
None of these is an error; they are different conventions. State the density and the convention next to any weight you quote.
Quick checks
Steel: thickness in inches × 40.84 gives lb/ft², and thickness in millimetres × 7.85 gives kg/m². Aluminum: × 14.05 lb/ft² per inch or × 2.7 kg/m² per mm. Stainless: × 41.62 lb/ft² per inch or × 8.0 kg/m² per mm. The commonest slips are forgetting the 144 in²/ft² or mixing millimetres with inches. Test any new spreadsheet on a known case, such as 1/4 in steel plate at 10.21 lb/ft², before trusting it.
Related calculators and pages
Questions about this guide
What is the formula for the weight of a steel plate?
Weight = length × width × thickness × density. In inches and pounds, multiply by 0.2836 lb/in³ for carbon steel. A 48 × 96 in plate that is 0.25 in thick weighs 48 × 96 × 0.25 × 0.2836 = 326.7 lb.
Is steel 7,850 or 7,870 kg/m³?
Both appear. 7,850 kg/m³ is the common handbook value for carbon steel; 7,870 is close to the density of pure iron (about 7,874). The difference is 0.25%, so results differ by about 25 kg per 10 tonnes.
How do I convert lb/in³ to kg/m³?
Multiply by 27,679.9. So 0.2836 lb/in³ is 7,850 kg/m³. In the other direction, multiply kg/m³ by 0.00003612729.
What is the weight of one square foot of steel one inch thick?
About 40.84 lb with 7,850 kg/m³. Multiply any steel thickness in inches by 40.84 to get lb/ft². Aluminum is 14.05 lb/ft² per inch and 304/316 stainless is 41.62.
More guides
- Why 16 Gauge Is Not One Thickness Four gauge charts, four thicknesses for the same number, with the exact 7–30 gauge tables and the formulas behind them.
- Sheet vs Plate vs Gauge: What to Call and How to Order The thickness and width thresholds that separate sheet, strip and plate in each metal, and how to write an unambiguous order.
- Pipe NPS vs OD vs Schedule NPS is a label, OD is fixed, schedule sets the wall: with the exact STD/Sch 40 and XS/Sch 80 overlaps.
- Theoretical vs Delivered Weight: Mill Tolerances How rolling and pipe tolerances (ASTM A6, A480, A53) and coatings make real weight differ from the calculated figure.
This guide is general information, not engineering advice. Check dimensions and weights against the governing standard and your supplier's mill certificate, and use a qualified engineer for structural, pressure or safety-critical work.