Skip to content
StockGauge Metal gauge · plate · bar · pipe

16 Gauge Galvanized Steel Thickness and Weight

A 16 gauge galvanized steel sheet is 0.0635 in (1.613 mm) thick. At 7,850 kg/m³ (0.2836 lb/in³) it weighs 2.593 lb/ft² (12.66 kg/m²), so a 4×8 ft sheet weighs 83.0 lb (37.6 kg) and a 1250×2500 mm sheet weighs 39.6 kg (87.2 lb).

Thickness
0.0635 in · 1.613 mm
Weight per ft²
2.593 lb
Weight per m²
12.66 kg
4×8 ft sheet
83.0 lb · 37.6 kg
1250×2500 mm sheet
39.6 kg · 87.2 lb
Density used
7,850 kg/m³ · 0.2836 lb/in³

Sheet metal gauge & plate weight calculator

Mode

Galvanized Sheet Gauge. MSG steel thickness plus about 0.0037–0.0038 in of zinc coating. Density 7,850 kg/m³ = 0.2836 lb/in³. Steel base density. The zinc coating is included in the published galvanized gauge thickness, not in the density.

Thickness

0.0635 in

1.61 mm

Per ft²

2.593 lb

12.66 kg/m²

4 × 8 ft sheet

82.98 lb

37.64 kg

1250 × 2500 mm

39.57 kg

87.23 lb

Gauge standard
Galvanized Sheet Gauge
Thickness
0.0635 in · 1.613 mm
Nearest gauge
16 ga on the Galvanized chart
Density
7,850 kg/m³ (0.2836 lb/in³)
Weight per ft²
2.593 lb
Weight per m²
12.66 kg
4 × 8 ft (48 × 96 in) sheet (32 ft²)
82.98 lb · 37.64 kg
1250 × 2500 mm sheet (3.125 m²)
87.23 lb · 39.57 kg
  • Galvanized gauge thickness includes the zinc coating. Published galvanized charts start at 8 gauge.

Worked calculation

  1. Look up the thickness. Galvanized Sheet Gauge, 16 ga = 0.0635 in. In millimetres: 0.0635 × 25.4 = 1.613 mm.
  2. State the density. Galvanized Steel: 7,850 kg/m³ = 0.2836 lb/in³ (1 lb/in³ = 27,679.9 kg/m³).
  3. Weight per square foot. 0.0635 in × 144 in²/ft² × 0.2836 lb/in³ ≈ 2.593 lb/ft².
  4. Weight per square metre. 1.613 mm × 7.85 kg/m²/mm (density ÷ 1,000) ≈ 12.66 kg/m².
  5. Weight of a 4×8 ft sheet. 2.593 lb/ft² × 32 ft² ≈ 83.0 lb (37.6 kg). For a 1250×2500 mm sheet: 12.66 kg/m² × 3.125 m² ≈ 39.6 kg.
  6. Compare with the published chart weight. MSG defines 16 ga as 2.500 lb/ft² nominal (0.0635 in × 41.82 lb/ft² per inch). The density-based 2.593 lb/ft² is -3.6% lower because 7,850 kg/m³ equals 40.84 lb/ft² per inch, not 41.82.

Reference tables

16 gauge in each chart (density-based weights)
ChartThickness (in)Thickness (mm)lb/ft²kg/m²4×8 ft sheet (lb)
Manufacturers' Standard Gauge (MSG) 0.05981.522.44211.9278.1
Stainless Steel Gauge (U.S. Standard progression) 0.06251.592.60112.7083.2
Brown & Sharpe / American Wire Gauge (AWG) 0.05081.290.7143.4822.8
Galvanized Sheet Gauge 0.06351.612.59312.6683.0

The same gauge number gives a different thickness in every chart.

Galvanized gauges around 16 ga
GaugeThickness (in)Thickness (mm)lb/ft²kg/m²4×8 ft sheet (lb)
14 ga 0.07851.993.20615.65103
15 ga 0.07101.802.90014.1692.8
16 ga 0.06351.612.59312.6683.0
17 ga 0.05751.462.34811.4675.1
18 ga 0.05161.312.10710.2967.4

Engineering and fabrication notes

16 gauge galvanized sheet is 0.0635 in (1.61 mm), about 0.0037 in thicker than 16 gauge carbon steel because the galvanized chart builds in the zinc coating. It is a typical thickness for ductwork, equipment housings and outdoor enclosures where bare steel would need paint. The 0.0635 in figure is sometimes mistaken for stainless 16 gauge, which is 0.0625 in. Weight here uses steel density for the whole thickness (2.593 lb/ft²), a slightly conservative figure because zinc is lighter than steel.

Frequently asked questions

What is the thickness of 16 gauge galvanized steel?

16 Gauge Galvanized Steel is 0.0635 in or 1.61 mm on the Galvanized Sheet Gauge chart. MSG steel thickness plus about 0.0037–0.0038 in of zinc coating.

How much does a 4×8 sheet of 16 gauge galvanized steel weigh?

A 4×8 ft (48 × 96 in) sheet of 16 gauge galvanized steel weighs about 83.0 lb (37.6 kg) using 7,850 kg/m³. That is 2.593 lb/ft² × 32 ft². Actual mill weight varies with thickness tolerance.

Is 16 gauge galvanized steel the same thickness as 16 gauge in other metals?

No. At 16 gauge the charts give 0.0598 in for carbon steel, 0.0625 in for stainless steel, 0.0508 in for aluminum and 0.0635 in for galvanized steel.

Does 16 gauge galvanized steel include the zinc coating?

Yes. The galvanized gauge chart adds about 0.0037–0.0038 in to the carbon steel thickness for the coating, so 16 ga galvanized is 0.0635 in against 0.0598 in for uncoated steel. Coating class (for example G60 or G90) is specified separately.