14 Gauge Aluminum Thickness and Weight
A 14 gauge aluminum (Brown & Sharpe) sheet is 0.0641 in (1.628 mm) thick. At 2,700 kg/m³ (0.0975 lb/in³) it weighs 0.900 lb/ft² (4.40 kg/m²), so a 4×8 ft sheet weighs 28.8 lb (13.1 kg) and a 1250×2500 mm sheet weighs 13.7 kg (30.3 lb).
- Thickness
- 0.0641 in · 1.628 mm
- Weight per ft²
- 0.900 lb
- Weight per m²
- 4.40 kg
- 4×8 ft sheet
- 28.8 lb · 13.1 kg
- 1250×2500 mm sheet
- 13.7 kg · 30.3 lb
- Density used
- 2,700 kg/m³ · 0.0975 lb/in³
Sheet metal gauge & plate weight calculator
Thickness
0.0641 in
1.63 mm
Per ft²
0.900 lb
4.40 kg/m²
4 × 8 ft sheet
28.81 lb
13.07 kg
1250 × 2500 mm
13.74 kg
30.29 lb
- Gauge standard
- Brown & Sharpe / American Wire Gauge (AWG)
- Thickness
- 0.0641 in · 1.628 mm
- Nearest gauge
- 14 ga on the B&S / AWG chart
- Density
- 2,700 kg/m³ (0.0975 lb/in³)
- Weight per ft²
- 0.900 lb
- Weight per m²
- 4.40 kg
- 4 × 8 ft (48 × 96 in) sheet (32 ft²)
- 28.81 lb · 13.07 kg
- 1250 × 2500 mm sheet (3.125 m²)
- 30.29 lb · 13.74 kg
Worked calculation
- Look up the thickness. Brown & Sharpe / American Wire Gauge (AWG), 14 ga = 0.0641 in. In millimetres: 0.0641 × 25.4 = 1.628 mm.
- State the density. Aluminum 6061 / 5052: 2,700 kg/m³ = 0.0975 lb/in³ (1 lb/in³ = 27,679.9 kg/m³).
- Weight per square foot. 0.0641 in × 144 in²/ft² × 0.0975 lb/in³ ≈ 0.900 lb/ft².
- Weight per square metre. 1.628 mm × 2.70 kg/m²/mm (density ÷ 1,000) ≈ 4.40 kg/m².
- Weight of a 4×8 ft sheet. 0.900 lb/ft² × 32 ft² ≈ 28.8 lb (13.1 kg). For a 1250×2500 mm sheet: 4.40 kg/m² × 3.125 m² ≈ 13.7 kg.
- Compare with the published chart weight. MSG defines 14 ga as 3.125 lb/ft² nominal (0.0641 in × 41.82 lb/ft² per inch). The density-based 0.900 lb/ft² is 247.1% lower because 7,850 kg/m³ equals 40.84 lb/ft² per inch, not 41.82.
Reference tables
| Chart | Thickness (in) | Thickness (mm) | lb/ft² | kg/m² | 4×8 ft sheet (lb) |
|---|---|---|---|---|---|
| Manufacturers' Standard Gauge (MSG) | 0.0747 | 1.90 | 3.051 | 14.89 | 97.6 |
| Stainless Steel Gauge (U.S. Standard progression) | 0.0781 | 1.98 | 3.250 | 15.87 | 104 |
| Brown & Sharpe / American Wire Gauge (AWG) | 0.0641 | 1.63 | 0.900 | 4.40 | 28.8 |
| Galvanized Sheet Gauge | 0.0785 | 1.99 | 3.206 | 15.65 | 103 |
The same gauge number gives a different thickness in every chart.
| Gauge | Thickness (in) | Thickness (mm) | lb/ft² | kg/m² | 4×8 ft sheet (lb) |
|---|---|---|---|---|---|
| 12 ga | 0.0808 | 2.05 | 1.135 | 5.54 | 36.3 |
| 13 ga | 0.0720 | 1.83 | 1.011 | 4.94 | 32.4 |
| 14 ga | 0.0641 | 1.63 | 0.900 | 4.40 | 28.8 |
| 15 ga | 0.0571 | 1.45 | 0.802 | 3.92 | 25.7 |
| 16 ga | 0.0508 | 1.29 | 0.714 | 3.48 | 22.8 |
Engineering and fabrication notes
14 gauge aluminum is 0.0641 in (1.63 mm), which stock lists usually round to 0.063 in (1/16 in). It is common for enclosures, brackets, panels, light signage and trim where 14 gauge steel (0.0747 in) would be heavier than needed: a square foot weighs 29.5% of the same-gauge carbon steel sheet. Stiffness falls faster than weight, though, because aluminum's elastic modulus is about one third of steel's, so a steel-to-aluminum swap usually needs a thicker gauge or added ribs.
Adjacent sizes and comparisons
- 12 gauge aluminum Next thicker gauge page
- 16 gauge aluminum Next thinner gauge page
- 14 gauge steel Same gauge number, different chart
- 14 gauge stainless steel Same gauge number, different chart
- 14 gauge steel vs 14 gauge aluminum Side-by-side comparison
- Sheet & plate weight calculator Any thickness, any size
- Why 16 gauge is not one thickness Reference guide
- All gauge pages Browse every gauge chart page
Frequently asked questions
What is the thickness of 14 gauge aluminum (Brown & Sharpe)?
14 Gauge Aluminum is 0.0641 in or 1.63 mm on the Brown & Sharpe / American Wire Gauge (AWG) chart. Geometric: d(n) = 0.005 × 92^((36 − n) / 39) in.
How much does a 4×8 sheet of 14 gauge aluminum (Brown & Sharpe) weigh?
A 4×8 ft (48 × 96 in) sheet of 14 gauge aluminum (Brown & Sharpe) weighs about 28.8 lb (13.1 kg) using 2,700 kg/m³. That is 0.900 lb/ft² × 32 ft². Actual mill weight varies with thickness tolerance.
Is 14 gauge aluminum the same thickness as 14 gauge in other metals?
No. At 14 gauge the charts give 0.0747 in for carbon steel, 0.0781 in for stainless steel, 0.0641 in for aluminum and 0.0785 in for galvanized steel.
What decimal thickness is closest to 14 gauge aluminum?
Aluminum gauge follows Brown & Sharpe / AWG: thickness = 0.005 × 92^((36 − 14) ÷ 39) = 0.0641 in. Of the round decimal thicknesses suppliers commonly stock (0.040, 0.050, 0.063, 0.080 and 0.100 in), 0.063 in is nearest, 1.7% thinner than the gauge value. Order by decimal thickness and alloy rather than by gauge number.